By request

    oppiFEEL

    Give your venue senses.

    A small kit of sensors that tells OPPI what the room is doing. How cold the coolroom is. How loud the floor is. How many people are in.

    Fitted to your venue by OPPI. Scoped and quoted per site.

    approx. 70 mm123456oppiFEEL03 / 07Cold probeIllustrated. Nominal sizes. Not to scale.

    Sheet 01

    The kit.

    One hub. Five kinds of sensor. Fit the ones your venue needs.

    1. 01Hub
    2. 02Cold probe
    3. 03Sound level sensor
    4. 04People counter
    5. 05Leak sensor
    6. 06Door contact

    Illustrated. Nominal sizes. Not to scale.

    approx. 180 mm123456oppiFEEL02 / 07HubIllustrated. Nominal sizes. Not to scale.

    Sheet 02

    The hub.

    One box that hears every sensor in the building and passes the readings to OPPI.

    What it feels

    • Every sensor in the kit, through walls and down to the cellar
    • Its own power and connection

    What OPPI does with it

    • Sends readings to OPPI and nowhere else
    • Tells OPPI when a sensor goes quiet or a battery runs low

    Where it goes

    Somewhere central with power. The office or behind the bar.

    Parts

    1. 1Wall bracket. Two screws. The hub clips on.
    2. 2Base shell. Power and network ports on the side.
    3. 3Main board. Power, network and the processor.
    4. 4Radio module. Listens for every sensor in the kit.
    5. 5Lid. Status light and vents.
    6. 6Antenna. Long range, low power.

    Needs mains power and an internet connection. One hub covers most venues. Large or multi-level sites may need a second.

    approx. 70 mm123456oppiFEEL03 / 07Cold probeIllustrated. Nominal sizes. Not to scale.

    Sheet 03

    Cold probe.

    A probe inside every fridge, freezer and coolroom, logging the temperature by itself.

    What it feels

    • The temperature inside the unit, every few minutes
    • A door left open, as a slow climb

    What OPPI does with it

    • Keeps the temperature log without anyone writing it down
    • Wakes the manager on duty when a unit stays warm, not when a door opens for a minute
    • Shows the whole cold chain on one screen

    Where it goes

    The transmitter sits outside the unit. The probe runs in through the door seal.

    Parts

    1. 1Magnetic mount. Holds to the outside of the unit.
    2. 2Back shell. Sealed against kitchen damp.
    3. 3Battery. Lasts years, not weeks.
    4. 4Board and radio. Reads the probe and reports to the hub.
    5. 5Front shell. A small screen shows the last reading.
    6. 6Probe and lead. The part that sits in the cold.

    A logging sensor, not a certified reference thermometer. Keep a hand probe for the checks your food safety plan asks a person to make.

    approx. 80 mm123456oppiFEEL04 / 07Sound level sensorIllustrated. Nominal sizes. Not to scale.

    Sheet 04

    Sound level sensor.

    A quiet ear on the room, so you hear about the volume before the neighbours do.

    What it feels

    • How loud the room is, as a level in decibels
    • The trend across the night

    What OPPI does with it

    • Warns the manager on duty when the room runs loud for your limit and your hour
    • Keeps a record of the night's levels to look back on

    Where it goes

    High on a wall, away from speakers. The courtyard, the band room, the boundary side.

    Parts

    1. 1Wall mount. Two screws or a pad.
    2. 2Back shell. Holds the batteries.
    3. 3Batteries. No cable to run.
    4. 4Board and radio. Works out the level and reports to the hub.
    5. 5Microphone. Hears level only. It does not record audio.
    6. 6Grille. Lets sound in, keeps dust out.

    An early warning, not a certified sound level meter. It gives one overall level. It is not evidence for a licence hearing, and a noise condition is still measured by an acoustic consultant.

    approx. 110 mm123456oppiFEEL05 / 07People counterIllustrated. Nominal sizes. Not to scale.

    Sheet 05

    People counter.

    A count at the door, so you know how many are in without a clicker.

    What it feels

    • People in and people out, at each doorway
    • How full the venue is against the number on your licence

    What OPPI does with it

    • Shows the head count to the door and the manager on duty
    • Warns before you reach capacity, not after
    • Gives the roster a true picture of how busy each hour was

    Where it goes

    Above each entry, looking down.

    Parts

    1. 1Door frame bracket. Fixes above the doorway.
    2. 2Body shell. Slim enough to sit on the frame.
    3. 3Batteries. No cable to run.
    4. 4Board and radio. Counts on the device and reports to the hub.
    5. 5Depth sensor. Sees direction, in and out.
    6. 6Window cover. Protects the sensor.

    Counts shapes, not faces. It takes no photos and identifies no one. Wide or crowded doorways count less exactly, so treat the number as a guide beside your door staff, not a replacement for them.

    approx. 60 mm12345oppiFEEL06 / 07Leak sensorIllustrated. Nominal sizes. Not to scale.

    Sheet 06

    Leak sensor.

    A puck on the floor that knows when it is standing in water.

    What it feels

    • Water on the floor, the moment it bridges the contacts

    What OPPI does with it

    • Wakes someone when the cellar, the glasswasher or the ice machine leaks overnight
    • Logs when it started and when it was dealt with

    Where it goes

    On the floor at the low point. Cellar, under the glasswasher, beside the ice machine.

    Parts

    1. 1Contacts. Water between them is the signal.
    2. 2Base shell. Sealed. Sits on the floor.
    3. 3Battery. A coin cell.
    4. 4Board and radio. Reports to the hub.
    5. 5Lid. Status light.

    Tells you there is water where it sits. It does not shut off the supply.

    approx. 60 mm123456oppiFEEL07 / 07Door contactIllustrated. Nominal sizes. Not to scale.

    Sheet 07

    Door contact.

    Two small parts that know whether a door is open or shut.

    What it feels

    • Open or shut, and for how long

    What OPPI does with it

    • Flags the coolroom door left ajar before the temperature climbs
    • Checks the cellar and the back door at close
    • Notes when a door opens outside trading hours

    Where it goes

    The sensor on the frame, the magnet on the door.

    Parts

    1. 1Adhesive mount. No drilling.
    2. 2Back shell. Sits on the door frame.
    3. 3Battery. A coin cell.
    4. 4Board and reed switch. The switch closes when the magnet is near.
    5. 5Lid. Clips on.
    6. 6Magnet. Rides on the door.

    It is not a lock or an alarm system. It does not replace a monitored alarm.

    Also by request.

    The same hub hears more than five things. Ask if your venue needs these.

    • Power on a circuit

      A clamp in the switchboard, fitted by an electrician. Shows a compressor that never rests and what stays on after close.

    • Air quality

      Carbon dioxide, temperature and humidity in the room. A fair sign of how crowded and how stuffy it is.

    How it is fitted.

    1. 01

      You ask

      Tell us the venue and what you want it to feel.

    2. 02

      We scope it

      Which sensors, how many, where they go. Quoted per site.

    3. 03

      We fit it

      OPPI supplies the kit and sets it up with you. Most sensors stick or screw on.

    4. 04

      OPPI feels it

      Readings go to OPPI and nowhere else. We support the kit after that.

    The plain limits.

    • oppiFEEL is fitted by request, venue by venue. It is not something you add at checkout.
    • The hardware is sourced, fitted and supported by OPPI. OPPI does not manufacture it.
    • The sound sensor is an early warning, not a certified meter.
    • The cold probes log temperature. They do not replace the checks your food safety plan asks a person to make.
    • Nothing here is a life-safety device. Gas alarms, duress buttons and monitored alarms stay with the systems built for them.
    • The people counter takes no photos and the sound sensor records no audio.

    Questions.

    What is oppiFEEL?
    oppiFEEL is a sensor kit for oppiOS. Cold probes, a sound level sensor, a doorway people counter, leak sensors and door contacts report through one hub to OPPI. It is fitted by request, venue by venue.
    How do I get oppiFEEL?
    Ask us. We scope which sensors your venue needs and where they go, then quote it per site. It is not sold at checkout.
    Does OPPI make the sensors?
    No. OPPI sources, fits and supports the hardware, and the readings go to OPPI only. OPPI does not manufacture the devices.
    Can the sound sensor prove I met my licence noise condition?
    No. It is an early warning that the room is running loud. It is not a certified sound level meter and is not evidence for a licence hearing. Noise conditions are measured by an acoustic consultant.
    Do the cold probes replace manual temperature checks?
    They log each unit's temperature by themselves and raise an alert when a unit stays warm. Keep a hand probe for the checks your food safety plan asks a person to make.
    Does the people counter film anyone?
    No. It counts shapes passing in and out and reports a number. It takes no photos and identifies no one.
    What does the kit need at the venue?
    One hub with mains power and an internet connection. The sensors run on batteries and report to the hub, so there are no cables to run to them.
    By request

    Tell us what you want your venue to feel.

    We will scope it and come back with a quote for your site.

    Ask about oppiFEEL